✦ LIBER ✦

Research on the cast molding process for high quality PDMS molds

✍ Scribed by Xiangdong Ye; Hongzhong Liu; Yucheng Ding; Hansong Li; Bingheng Lu

Publisher: Elsevier Science
Year: 2009
Tongue: English
Weight: 862 KB
Volume: 86
Category: Article
ISSN: 0167-9317
DOI: 10.1016/j.mee.2008.10.011

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Improved mold fabrication for the defini

Improved mold fabrication for the definition of high quality nanopatterns by Soft UV-Nanoimprint lithography using diluted PDMS material

✍ Namil Koo; Markus Bender; Ulrich Plachetka; Andreas Fuchs; Thorsten Wahlbrink; J 📂 Article 📅 2007 🏛 Elsevier Science 🌐 English ⚖ 830 KB

The surface treatment of polypropylene m

The surface treatment of polypropylene molds and its effect on the quality of cast contact lenses

✍ Dr. J. Lukášk; T. Fenclová; V. Tyráčkková; J. Vacík 📂 Article 📅 1992 🏛 Wiley (John Wiley & Sons) 🌐 English ⚖ 534 KB

An investigation of the surface by XPS photoelectron spectroscopy has shown that the process of production of cast contact lenses based on poly(2-hydroxyethyl methacrylateco-diethyleneglycol methacrylate) is accompanied by mass transfer at the lens-mold boundary. This phenomenon, which impairs the c

Review of research in the determination

Review of research in the determination of process parameters for plastic injection molding

✍ S. L. Mok; C. K. Kwong; W. S. Lau 📂 Article 📅 1999 🏛 John Wiley and Sons 🌐 English ⚖ 228 KB 👁 2 views

This article aims to review the research in determining process parameters of injection molding. A number of research works based on various approaches have been performed in the domain of the parameter setting for injection molding. These approaches, including mathematical models, numerical simulat

Effect of crystallization behavior of mo

Effect of crystallization behavior of mold flux on slab surface quality of a Ti-bearing Fe–Cr–Ni super alloy cast by means of continuous casting process

✍ Hidekazu Todoroki; Teruaki Ishii; Kenji Mizuno; Atsuya Hongo 📂 Article 📅 2005 🏛 Elsevier Science 🌐 English ⚖ 963 KB

Effects of molecular structure on the rh

Effects of molecular structure on the rheology and processability of blow-molding high-density polyethylene resins

✍ Alfonsius B. Ariawan; Savvas G. Hatzikiriakos; Shivendra K. Goyal; Henry Hay 📂 Article 📅 2001 🏛 John Wiley and Sons 🌐 English ⚖ 445 KB 👁 2 views

On the synthesis of poly(ε-caprolactam)—

On the synthesis of poly(ε-caprolactam)—poly(butadiene-co-acrylonitrile) block copolymers for the reaction injection molding process

✍ Jaroslav Stehlíček; Frantiček Lednický; Josef Baldrian; Jan Šebenda; Emil Neuhäu 📂 Article 📅 1991 🏛 Society for Plastic Engineers 🌐 English ⚖ 906 KB

## Abstract The liquid rubbers Hycar ATBN and HTBN were used in the preparation of poly(ε‐caprolactam)—poly(butadiene‐co‐acrylonitrile) block copolymers intended for reaction injection molding by the anionic polymerization of ε‐caprolactam. The conversion of Hycar end groups to polymerization growt