𝔖 Bobbio Scriptorium
✦   LIBER   ✦

Design of V-shaped microstrip patch antenna at 2.4 GHz

✍ Scribed by Sudip Kumar Murmu; Iti Saha Misra

Book ID
102950763
Publisher
John Wiley and Sons
Year
2011
Tongue
English
Weight
967 KB
Volume
53
Category
Article
ISSN
0895-2477

No coin nor oath required. For personal study only.

✦ Synopsis

Abstract

A V‐shaped microstrip patch antenna for 2.4 GHz is designed, fabricated, and experimentally measured. The proposed antenna is designed on glass‐epoxy substrate. Here, coaxial probe feed is used to provide the RF power to the patch. The proposed design provides 50 MHz impedance bandwidth determined from 10 dB return loss for 2.4 GHz frequency band, respectively. The design is simulated using the Ansoft HFSS simulation tool. © 2011 Wiley Periodicals, Inc. Microwave Opt Technol Lett 53:806–811, 2011; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.25877

📜 SIMILAR VOLUMES

Design of H-shaped microstrip patch ante
Design of H-shaped microstrip patch antennas
✍ S. F. Ooi; S. K. Lee; A. Sambell; E. Korolkiewicz; S. Scott 📂 Article 📅 2007 🏛 John Wiley and Sons 🌐 English ⚖ 318 KB 👁 1 views

## Abstract Based on the symmetric properties of the antenna, the design equations for the first four mode frequencies are derived. A design methodology for an antenna operating at 2.45 GHz is presented. Two antennas have been designed and tested, and good agreement among the predicted, simulated,

Design of multiple U-shaped slot microst
Design of multiple U-shaped slot microstrip patch antenna for 5-GHz band WLANs
✍ Jeong Min Ju; Gyey-Teak Jeong; Joong-Han Yoon; Sung-Won Ko; Kyung-Sup Kwak 📂 Article 📅 2004 🏛 John Wiley and Sons 🌐 English ⚖ 219 KB 👁 1 views

## Abstract In this study, a multiple U‐shaped slot microstrip patch antenna for application in the 5‐GHz band is designed and fabricated. To obtain sufficient bandwidth in the operating band, foam is inserted between the substrate and ground plane, a coaxial probe source is used, and the position

Design of a dual-band V-shaped monople a
Design of a dual-band V-shaped monople antenna for DCS/2.4-GHz WLAN operations
✍ Hatem Rmili; Jean-Marie. Floc'h 📂 Article 📅 2008 🏛 John Wiley and Sons 🌐 English ⚖ 187 KB 👁 1 views

## Abstract In this article, we present a simple surface‐mountable monopole antenna for dual‐band DCS1800 and 2.4‐GHz WLAN operations. The antenna was obtained by folding a metallic strip into a V‐shape, and soldered to a 50‐Ω microstrip feed line printed on a metallized substrate. The proposed ant

Fabrication and measurement of an arrow-
Fabrication and measurement of an arrow-shaped microstrip patch antenna in the 5-GHz band
✍ Jeong-Min Ju; Joong-Han Yoon; Sung-Won Ko; Moon-Gyu Kang; Kyung-Sup Kwak 📂 Article 📅 2004 🏛 John Wiley and Sons 🌐 English ⚖ 280 KB 👁 1 views

## Abstract In this paper, an arrow‐shaped microstrip patch antenna is designed, fabricated, and measured for a 5‐GHz band wireless local area network (WLAN) application. The geometry of our proposed antenna is suitable for the wideband antenna in the 5‐GHz band. To obtain sufficient bandwidth in t

Design of multiple U-shaped slot microst
Design of multiple U-shaped slot microstrip patch antenna in Hiper-LAN band
✍ GyeyTeak Jeong; Joong-Han Yoon; Sang Mok Lee; Kyung-Sup Kwak 📂 Article 📅 2004 🏛 John Wiley and Sons 🌐 English ⚖ 235 KB 👁 1 views

## Abstract In this paper, a multiple U‐shaped slot antenna is described, designed, fabricated, and measured for Hiper‐LAN. The design is based on a U‐shaped slot and two inverted U‐shaped slots. To obtain sufficient bandwidth, a foam layer is inserted between the ground plane and substrate. A meas

Design of a dual-band π-shaped microstri
Design of a dual-band π-shaped microstrip patch antenna with a shorting pin for 5.2/5.8 GHz WLAN systems
✍ Sun-Ho Choi; Daehan Kwak; Hwa-Choon Lee; Kyung-Sup Kwak 📂 Article 📅 2010 🏛 John Wiley and Sons 🌐 English ⚖ 173 KB

## Abstract This article describes the design, fabrication, and measurement of a novel π‐shaped dual‐band antenna with a shorting pin for 5.2/5.8 GHz wireless local area network (WLAN) systems.To obtain sufficient bandwidth when return loss (RL) < −10 dB, a shorting pin is inserted in the patch and