✦ LIBER ✦

The effect of RRA on the strength and SCC resistance on AA7050 and AA7150 aluminium alloys

✍ Scribed by A.F Oliveira Jr.; M.C de Barros; K.R Cardoso; D.N Travessa

Publisher: Elsevier Science
Year: 2004
Tongue: English
Weight: 403 KB
Volume: 379
Category: Article
ISSN: 0921-5093
DOI: 10.1016/j.msea.2004.02.052

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

The kinetics and mechanisms of filiform

The kinetics and mechanisms of filiform corrosion on aluminium alloy AA6111

✍ H.N. McMurray; A. Holder; G. Williams; G.M. Scamans; A.J. Coleman 📂 Article 📅 2010 🏛 Elsevier Science 🌐 English ⚖ 776 KB

Scanning Kelvin Probe (SKP) potentiometry is used to investigate the effect of surface abrasion and heat treatment on the open-circuit potential (OCP) of AA6111 in humid air. SKP is also used to follow the kinetics of filiform corrosion (FFC) and to determine characteristic potentials associated wit

Effect of homogenization and precipitati

Effect of homogenization and precipitation treatments on the hot workability of an aluminium alloy AA2024

✍ P. Wouters; B. Verlinden; H.J. McQueen; E. Aernoudt; L. Delaey; S. Cauwenberg 📂 Article 📅 1990 🏛 Elsevier Science 🌐 English ⚖ 574 KB

Hot-torsion tests have been carried out at 310 and 370 °C (at a strain rate of l s-i) on an AA 2024 aluminium alloy homogenized for 8 h at between 420 and 520 °C and either just water quenched or air cooled and aged at 290 or 350 °C. The flow curves exhibited a large peak stress ap and work softenin

Gauge reduction in Twin-Roll Casting of

Gauge reduction in Twin-Roll Casting of an AA5052 aluminium alloy: The effects on microstructure

✍ B.S. Berg; V. Hansen; P.T. Zagierski; M.L. Nedreberg; A. Olsen; J. Gjønnes 📂 Article 📅 1995 🏛 Elsevier Science 🌐 English ⚖ 623 KB

Influence of Microstructure on the Quasi

Influence of Microstructure on the Quasistatic and Low Cycle Fatigue Behaviour of an AA2618 Aluminium Alloy

✍ Osama Khalil; Karl-Heinz Lang 📂 Article 📅 2011 🏛 Elsevier 🌐 English ⚖ 388 KB

The high-strength aluminium alloy AA2618 is a typical material to manufacture centrifugal compressor wheels of exhaust turbochargers. In general these components are manufactured from heat treated forged slugs. Depending on the size of the slugs during the heat treatment different microstructure may

The effect of cold rolling and annealing

The effect of cold rolling and annealing on the serrated yielding phenomenon of AA5182 aluminum alloy

✍ Wei Wen; J.G. Morris 📂 Article 📅 2004 🏛 Elsevier Science 🌐 English ⚖ 895 KB

The effect of recrystallization on corro

The effect of recrystallization on corrosion and electrochemical behavior of 7150 Al alloy

✍ G. S. Peng; K. H. Chen; H. C. Fang; S. Y. Chen; H. Chao 📂 Article 📅 2009 🏛 John Wiley and Sons 🌐 German ⚖ 848 KB

## Abstract By weight loss, potentiodynamic polarization, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS) techniques complemented by optical and scanning electron microscopy observations, the effect of recrystallization on the corrosion, and electrochemical behavior of 7150 Al