𝔖 Bobbio Scriptorium
✦   LIBER   ✦

Analysis of failure in ‘Recoil from tension’ of pan-based carbon fibers

✍ Scribed by Jiang Hao; A.S. Abhiraman; K. Tsui

Publisher
Elsevier Science
Year
1993
Tongue
English
Weight
898 KB
Volume
31
Category
Article
ISSN
0008-6223

No coin nor oath required. For personal study only.

✦ Synopsis

Results from a study of the "recoil from tension" method for estimating the compressive strength of the poiyacrylonitrile (PAN)-based carbon fibers are reported here. Analysis of the effect of different gauge lengths on the recoil strength distribution and the fracture morphological features of cross sections of the tested filaments imply that both axial recoil and bending influence the recoil failure of PAN-based carbon fibers. The experimental recoil strength distributions have been compared to logistic and weibull models. A universal logistic model that incorporates a dependence on gauge length has been found to provide a good fit to the distributions obtained at different gauge lengths. This analytical expression can be used to obtain a physically meaningful extrapolated average "zero gauge length" recoil strength. which might be appropriate for estimating the true axial compressive strength of fibers.

Key Wards-Carbon fibers, failure, PAN fibers. recoil from tension, compressive strength.

📜 SIMILAR VOLUMES

Evolution of microvoids in PAN-based car
Evolution of microvoids in PAN-based carbon fibers
✍ Deng-hua Li; Gang-ping Wu; Chun-xiang Lu; Yong-hong Li; Fu He; Zhi-hai Feng; Xiu 📂 Article 📅 2010 🏛 Elsevier Science 🌐 English ⚖ 38 KB

instead of the commonly-used alkaline-acid method. The process parameters were optimized. Results showed that the fixed carbon mass fraction achieved by this method could be as high as 99.9% under the optimal conditions while that by the alkaline-acid method was only 85.8%, indicating that the alkal

Influence of tension during oxidative st
Influence of tension during oxidative stabilization on SO2 adsorption characteristics of polyacrylonitrile (PAN) based activated carbon fibers
✍ Joong Kee Lee; Heui Jong Shim; Jong Choo Lim; Guang Jin Choi; Young dae Kim; Byu 📂 Article 📅 1997 🏛 Elsevier Science 🌐 English ⚖ 651 KB

PAN-based carbon fibers were stabilized under various tensions in the presence of air at 230°C and sequentially activated at 950°C following carbonization. The prepared carbon fibers were tested for their SO2 adsorption capacity using a thermogravimeter. The magnitude of tension during stabilization

Improving preferred orientation and mech
Improving preferred orientation and mechanical properties of PAN-based carbon fibers by pretreating precursor fibers in nitrogen
✍ Xianying Qin; Yonggen Lu; Hao Xiao; Yuchen Hao; Ding Pan 📂 Article 📅 2011 🏛 Elsevier Science 🌐 English ⚖ 159 KB

which must operate at low temperature. In addition, the easy dispersion of the array of nanowires has been demonstrated. This process is thus an interesting method to produce large quantities of individual Ni-filled CNT.

Exploratory experiments in the conversio
Exploratory experiments in the conversion of plasticized melt spun PAN-based precursors to carbon fibers
✍ Dale Grove; P. Desai; A.S. Abhiraman 📂 Article 📅 1988 🏛 Elsevier Science 🌐 English ⚖ 994 KB

Current carbon fiber production from acrylic fibers employ wet or dry spun PAN-based precursors that require expensive solvents and costly solvent recovery methods. Recently, it has been discovered that melt spun PAN-based fibers can be prepared by using water as a plasticizer to lower the viscosity