✦ LIBER ✦

The effect of realistic coating properties on interfacial stresses in porous coated hip endoprostheses

Publisher: Elsevier Science
Year: 1994
Tongue: English
Weight: 117 KB
Volume: 27
Category: Article
ISSN: 0021-9290
DOI: 10.1016/0021-9290(94)90117-1

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Effect of porous coating geometry on int

Effect of porous coating geometry on interfacial stress under a shear load

✍ Wolfarth, Debra ;Ducheyne, Paul 📂 Article 📅 1993 🏛 John Wiley and Sons 🌐 English ⚖ 438 KB

## Abstract Porous coated implants are loaded under both bending and shear loading. Previously, the effect of various parameters on fatigue strength under a bending load has been determined. The interfacial geometry between the porous coating and the substrate was found to increase stress concentra

Effects of ingrowth, geometry, and mater

Effects of ingrowth, geometry, and material on stress transfer under porous-coated hip surface replacements

✍ Dr. D. P. Fyhrie; D. R. Carter; D. J. Schurman 📂 Article 📅 1988 🏛 Elsevier Science 🌐 English ⚖ 945 KB

Three different interface geometries for porous ingrowth surface replacements of the hip were examined using two-dimensional linear and nonlinear contact finite element analyses. The results indicate that incorporation of a nearly flat prosthesis interface between the surface replacement and the und

Effect of a change in interfacial geomet

Effect of a change in interfacial geometry on the fatigue strength of porous-coated Ti-6Al-4V

✍ Wolfarth, D. ;Ducheyne, P. 📂 Article 📅 1994 🏛 John Wiley and Sons 🌐 English ⚖ 925 KB

Porous-coated Ti-6A1-4V has a fatigue strength approximately one-third that of the uncoated alloy. The interfacial geometry between the porous coating and the implant substrate is notchlike, leading to stress concentrations that have been shown to be the main cause for the reduction in fatigue stren

The effects of processing variables on s

The effects of processing variables on stress development in ultraviolet-cured coatings

✍ Jason A. Payne; Lorraine F. Francis; Alon V. McCormick 📂 Article 📅 1997 🏛 John Wiley and Sons 🌐 English ⚖ 359 KB 👁 2 views

A cantilever deflection technique was used to monitor stress development during ultraviolet photo-cure of acrylate coatings to the glassy state. Two coating systems were studied: a trifunctional monomer (trimethylol propane triacrylate, TMPTA) and a tetrafunctional monomer (pentaerythritol tetraacry

Femoral prosthesis implantation induces

Femoral prosthesis implantation induces changes in bone stress that depend on the extent of porous coating

✍ Dr. Harry B. Skinner; Agnes S. Kim; Joyce H. Keyak; C. D. Mote Jr 📂 Article 📅 1994 🏛 Elsevier Science 🌐 English ⚖ 939 KB

## Abstract The objective of this study was to evaluate the effect of implantation of porous‐coated anatomic medullary fitting prostheses on stress in the proximal femur. Three‐dimensional finite element models of a cadaveric femur before and after implantation were used to evaluate the resulting c

The effect of a nanothickness coating on

The effect of a nanothickness coating on rough titanium substrate in the osteogenic properties of human bone cells

✍ Camilla C. G. Moura; Maria A. Souza; Paula Dechichi; Darceny Zanetta-Barbosa; Cr 📂 Article 📅 2010 🏛 John Wiley and Sons 🌐 English ⚖ 529 KB

## Abstract This study evaluated the effect of a bioactive ceramic coating, in the nanothickness range, onto a moderately rough surface on the osteogenic behavior of human bone cells. The cells were harvested from the mandibular mental region and were cultured over Ti‐6Al‐4V disks of different surf