✦ LIBER ✦

The bond strength of composite materials to human dental enamel

✍ Scribed by T. Low; J.A. von Fraunhofer

Publisher: Elsevier Science
Year: 1976
Weight: 654 KB
Volume: 4
Category: Article
ISSN: 0376-4583
DOI: 10.1016/0376-4583(76)90022-4

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Correlation between strength of bonding

Correlation between strength of bonding to enamel and mechanical properties of dental composites

✍ Boyer, Daniel B. ;Chalkley, Yvonne ;Chan, Kai Chiu 📂 Article 📅 1982 🏛 John Wiley and Sons 🌐 English ⚖ 460 KB 👁 2 views

## Abstract The strength of bonding of dental composites to enamel was measured in shear. The compressive strength, proportional limit, elastic modulus, and tensile strength of the composites were measured for correlation with the bond strength. Conventional and microfilled composites with a range

Microtensile bond strength of composite

Microtensile bond strength of composite resin to human enamel prepared using erbium: Yttrium aluminum garnet laser

✍ Carina Sinclér Delfino; Wanessa Christine Souza-Zaroni; Silmara Aparecida Milori 📂 Article 📅 2006 🏛 John Wiley and Sons 🌐 English ⚖ 116 KB 👁 1 views

## Abstract The Erbium: Yttrium Aluminum Garnet (YAG) laser used for preparation of cavity can alter the substrate and it could influence the bond strength of enamel. The aim of this __in vitro__ study was to evaluate the influence of Er:YAG laser's energy using microtensile bond test. Three groups

Influence of an optically thick water la

Influence of an optically thick water layer on the bond-strength of composite resin to dental enamel after IR laser ablation

✍ Michal Staninec; John Xie; Charles Q. Le; Daniel Fried 📂 Article 📅 2003 🏛 John Wiley and Sons 🌐 English ⚖ 198 KB 👁 1 views

## Abstract ## Background and Objectives Several studies of hard tissue ablation with Er:YAG lasers have shown that the addition of an optically thick water layer (∼1 mm) added to the surface of dental enamel before each incident laser pulse, profoundly influences the rate and efficiency of ablati

Effect of elapsed time following bleachi

Effect of elapsed time following bleaching on the shear bond strength of composite resin to enamel

✍ Nimet Unlu; Funda Kont Cobankara; Fusun Ozer 📂 Article 📅 2008 🏛 John Wiley and Sons 🌐 English ⚖ 166 KB 👁 2 views

## Abstract The purpose of this study was to investigate the effect of post‐treatment time on the shear bond strength of composite resin to enamel after bleaching with 10% carbamide peroxide (CP) and 35% hydrogen peroxide (HP) bleaching systems. One hundred and thirty‐five flattened labial enamel s

Comparison of the bond strength of compo

Comparison of the bond strength of composite resin to Er:YAG laser irradiated human enamel pre-treated with various methods In Vitro

✍ Masahito Otsuki; Toru Eguro; Toru Maeda; Hisayoshi Tanaka 📂 Article 📅 2002 🏛 John Wiley and Sons 🌐 English ⚖ 490 KB 👁 2 views

## Abstract ## Background and Objective We have reported that the application of ultrasonic scalers on the Er:YAG laser‐irradiated enamel surface achieved bond strengths of approximately 16 MPa. However, it is reported that a bond strength of 20 MPa is needed to prevent the maginal gaps, so the te

Effect of the tooth microstructure on th

Effect of the tooth microstructure on the shear bond strength of a dental composite

✍ Panighi, M. ;G'Sell, C. 📂 Article 📅 1993 🏛 John Wiley and Sons 🌐 English ⚖ 720 KB

Plane human enamel and dentin surfaces were used for microstructural investigation and shear bond testing. The dental tissue microstructure was characterized through the surface topology, the concentration in mineral elements (determined by electron microprobe analysis), and the Vickers microhardnes