✦ LIBER ✦

Study of the fine crystalline structure of polyethylenes via annealing and thermal fractionation

✍ Scribed by Yunchuan Xie; Qian Zhang; Xiaodong Fan

Publisher: John Wiley and Sons
Year: 2003
Tongue: English
Weight: 96 KB
Volume: 89
Category: Article
ISSN: 0021-8995
DOI: 10.1002/app.12387

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Study on molecular chain heterogeneity o

Study on molecular chain heterogeneity of linear low-density polyethylene by cross-fractionation of temperature rising elution fractionation and successive self-nucleation/annealing thermal fractionation

✍ Jie Kong; Xiaodong Fan; Yunchuan Xie; Wenqiang Qiao 📂 Article 📅 2004 🏛 John Wiley and Sons 🌐 English ⚖ 134 KB 👁 2 views

A General Method for the Anodic Formatio

A General Method for the Anodic Formation of Crystalline Metal Oxide Nanotube Arrays without the Use of Thermal Annealing

✍ Nageh K. Allam; Karthik Shankar; Craig A. Grimes 📂 Article 📅 2008 🏛 John Wiley and Sons 🌐 English ⚖ 406 KB 👁 2 views

Structure and thermal stability of polys

Structure and thermal stability of polysaccharide fractions extracted from the ultrasonic irradiated and cold alkali pretreated bamboo

✍ Ming-Fei Li; Yong-Ming Fan; Feng Xu; Run-Cang Sun 📂 Article 📅 2011 🏛 John Wiley and Sons 🌐 English ⚖ 493 KB 👁 1 views

Influence of previous annealing on first

Influence of previous annealing on first stage of degradation of blends of low-density polyethylene and Mater-Bi AF05H aged in soil: Comparative thermal analysis study

✍ A. Vallés-Lluch; L. Contat-Rodrigo; A. Ribes-Greus 📂 Article 📅 2003 🏛 John Wiley and Sons 🌐 English ⚖ 233 KB 👁 2 views

## Abstract Samples of low‐density polyethylene (LDPE) filled with a commercial biodegradable material (Mater‐Bi AF05H) were subjected to an accelerated soil burial test in a culture oven. In addition, another series of these blends was subjected to thermal treatment and afterward buried in soil un

Fine-structure and physical properties o

Fine-structure and physical properties of polyethylene fibers in high-speed spinning. I. Effect of melt-flow rate in the high-density polyethylene

✍ H. H. Cho; K. H. Kim; H. Ito; T. Kikutani 📂 Article 📅 2000 🏛 John Wiley and Sons 🌐 English ⚖ 365 KB 👁 2 views

High-density polyethylene (HDPE) fibers, obtained from a melt-flow rate (g/10 min) of 11 and 28, was produced by a high-speed melt-spinning method in the range of take-up velocity from 1 to 8 km/min and from 1 to 6 km/min, respectively. The change of fiber structure and physical properties with incr

Study of the Structure of Porous Silicon

Study of the Structure of Porous Silicon via Positron Annihilation Experiments

✍ Biasini, M. ;Ferro, G. ;Monge, M.A. ;Di Francia, G. ;La Ferrara, V. 📂 Article 📅 2000 🏛 John Wiley and Sons 🌐 English ⚖ 91 KB 👁 2 views