✦ LIBER ✦

Structure and mechanical properties of hot extruded YuNDK24 alloy

✍ Scribed by A. K. Izgorodin; Yu. V. Konoplev; V. V. Pasechnaya

Publisher: Springer US
Year: 1982
Tongue: English
Weight: 611 KB
Volume: 24
Category: Article
ISSN: 0026-0673
DOI: 10.1007/bf00772755

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Microstructure and mechanical properties

Microstructure and mechanical properties of a hot-hydrostatically extruded 93W–4.9Ni–2.1Fe alloy

✍ Yu Yang; Hu Lianxi; Wang Erde 📂 Article 📅 2006 🏛 Elsevier Science 🌐 English ⚖ 545 KB

Properties of hot-extruded antifriction

Properties of hot-extruded antifriction graphitic aluminum alloy

✍ G. L. Tsarev; A. P. Chelyshev; A. T. Volochko; G. I. Bortnik; V. F. Malyshev 📂 Article 📅 1986 🏛 Springer 🌐 English ⚖ 407 KB

Fatigue properties of the hot extruded m

Fatigue properties of the hot extruded magnesium alloy AZ31

✍ Michael Huppmann; Martin Lentz; Katrin Brömmelhoff; Walter Reimers 📂 Article 📅 2010 🏛 Elsevier Science 🌐 English ⚖ 646 KB

Effects of yttrium on microstructure and

Effects of yttrium on microstructure and mechanical properties of hot-extruded Mg–Zn–Y–Zr alloys

✍ Ya Zhang; Xiaoqin Zeng; Liufa Liu; Chen Lu; Hantao Zhou; Qiang Li; Yanping Zhu 📂 Article 📅 2004 🏛 Elsevier Science 🌐 English ⚖ 924 KB

This article studied the effects of yttrium on microstructure and mechanical properties of extruded Mg–Zn–Y–Zr alloys. Three kinds of Mg–5.5Zn–xY–0.4Zr alloys with variable yttrium content were hot-extruded at different temperature to investigate the microstructure evolution and dynamic recrystalliz

Hot deformation and processing maps of e

Hot deformation and processing maps of extruded ZE41A magnesium alloy

✍ S. Anbuselvan; S. Ramanathan 📂 Article 📅 2010 🏛 Elsevier Science ⚖ 639 KB

The hot deformation behavior and microstructure evolution of extruded ZE41A magnesium alloy has been studied using the processing map. The compression tests were conducted in the temperature range of 250-450 °C and the strain rate range of 0.001-1.0 s À1 to establish the processing map. The dynamic

Microstructure and mechanical properties

Microstructure and mechanical properties of spray deposited and extruded/heat treated hypoeutectic Al–Si alloy

✍ L.A. Bereta; C.F. Ferrarini; C.S. Kiminami; W.J.F. Botta; C. Bolfarini 📂 Article 📅 2007 🏛 Elsevier Science 🌐 English ⚖ 458 KB

The microstructure and the tensile properties of an Al-8.9 wt.% Si-3.2 wt.% Cu-0.9 wt.% Fe-0.8% Zn alloy processed by spray forming was investigated. The porosity level, the conditions of the heat treatment applied and the presence/addition of certain alloying elements to this alloy is known to grea