✦ LIBER ✦

Small chip dielectric antenna for Bluetooth application

✍ Scribed by Jung-Ick Moon; Seong-Ook Park

Publisher: John Wiley and Sons
Year: 2003
Tongue: English
Weight: 178 KB
Volume: 39
Category: Article
ISSN: 0895-2477
DOI: 10.1002/mop.11218

No coin nor oath required. For personal study only.

✦ Synopsis

Abstract

This paper proposes the design of a small chip‐type dielectric antenna using the advanced meander line technique, so that the radiation metals are formed on the bottom face of a ceramic dielectric (8 × 4 × 1.5 mm^3^, alumina) and on both faces of the substrate (thickness 1.0 mm, FR‐4). The performance of the proposed antenna mode, which remarkably reduced the size, shows good agreement between measured and computed results. The measured results show that this antenna has 11.2% bandwidth (2.35–2.63 GHz, |S~11~| < −10 dB) and 2.3‐dBi maximum radiation gain, respectively. © 2003 Wiley Periodicals, Inc. Microwave Opt Technol Lett 39: 366–368, 2003; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/mop.11218

📜 SIMILAR VOLUMES

Small printed integrated inverted-F ante

Small printed integrated inverted-F antenna for Bluetooth application

✍ Mohammod Ali; Gerard J. Hayes 📂 Article 📅 2002 🏛 John Wiley and Sons 🌐 English ⚖ 378 KB 👁 1 views

## Abstract A printed integrated inverted‐F antenna is introduced which operates in the Bluetooth frequency band (2.4–2.485 GHz). The proposed antenna is a part of the radio frequency printed circuit board (PCB) of a cellular telephone or a personal digital assistant (PDA). The antenna being an int

EBG-assisted slot antenna for Bluetooth

EBG-assisted slot antenna for Bluetooth applications

✍ Muhammad Faeyz Karim; H. Ghafouri-Shiraz 📂 Article 📅 2006 🏛 John Wiley and Sons 🌐 English ⚖ 430 KB 👁 1 views

A large-bandwidth patch antenna with a ridge-shaped ground plate is introduced. The patch with an air substrate is excited by a coaxial probe which is stretched from the top of a ridge-shaped ground plate; thus, the probe inductance is reduced and broadband operation is obtained. Its measured impeda

Broadband dual-polarization stacked micr

Broadband dual-polarization stacked microstrip antennas for Bluetooth applications

✍ Zhi Ning Chen; T. S. P. See; M. Y. W. Chia 📂 Article 📅 2003 🏛 John Wiley and Sons 🌐 English ⚖ 132 KB

## Abstract In this paper, a novel linear dual‐polarized stacked microstrip antenna that operates well within the ISM band (2.40–2.4835 GHz) for Bluetooth applications is experimentally presented. The square patch of the microstrip antenna is fed diagonally by a microstrip line. Another square patc

Small-size surface-mountable circularly

Small-size surface-mountable circularly polarized ceramic-chip antenna for GPS application

✍ Yeh-Chian Lin; Tsung-Wen Chiu; Kin-Lu Wong 📂 Article 📅 2004 🏛 John Wiley and Sons 🌐 English ⚖ 118 KB 👁 1 views

## Abstract A small‐size circularly polarized ceramic‐chip antenna suitable for surface mounting on a system circuit board is presented. The antenna mainly comprises a square radiating patch with a cross slot on the top surface, a square ground plane on the bottom surface, and a side‐feed conformal

A new microstrip patch antenna for mobil

A new microstrip patch antenna for mobile communications and bluetooth applications

✍ Binu Paul; S. Mridula; C. K. Aanandan; P. Mohanan 📂 Article 📅 2002 🏛 John Wiley and Sons 🌐 English ⚖ 117 KB 👁 1 views

## Abstract A compact multiband planar octagonal‐shaped microstrip antenna simultaneously suitable for mobile communication and blue tooth application is presented. The antenna provides sufficient isolation between the two operating bands and an area reduction of ≈29 % with respect to a circular pa

Characteristics of a two-layer microstri

Characteristics of a two-layer microstrip patch antenna for Bluetooth applications

✍ Lu Lu; Jacob Carl Coetzee 📂 Article 📅 2006 🏛 John Wiley and Sons 🌐 English ⚖ 99 KB 👁 1 views

## Abstract A double‐layer rectangular patch microstrip antenna suitable for Bluetooth applications is investigated. The patch is etched on a separate substrate which is suspended above the ground plane and supported by an MCX connector. The air gap between the patch and the ground plane increases