✦ LIBER ✦

Preparation of ultrafine superconducting YBCO particles by wet jet-mill

✍ Scribed by H. Kezuka; Y. Miyanaga; C. Kan-Nari; N. Maeda

Book ID: 113300625
Publisher: Elsevier Science
Year: 1996
Tongue: English
Weight: 348 KB
Volume: 44
Category: Article
ISSN: 0254-0584
DOI: 10.1016/0254-0584(95)01665-h

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Properties of nanophase grains of superc

Properties of nanophase grains of superconducting YBCO prepared by wet-type jet mill

✍ H. Kezuka; Zhonghe Xi; Y. Miyanaga; C. Kan-nari 📂 Article 📅 1996 🏛 Elsevier Science 🌐 English ⚖ 906 KB

Synthesis of fine particle-YBCO supercon

Synthesis of fine particle-YBCO superconductor by wet-type jet mill with methyl-ethyl-ketone

✍ H. Kezuka; N. Hosokawa; K. Hirata; K. Ishibashi; R. Kan-nari; T. Naito 📂 Article 📅 1995 🏛 Elsevier Science 🌐 English ⚖ 239 KB

State of the Dispersant and Particle Sur

State of the Dispersant and Particle Surface During Wet-Jet Milling for Preparation of a Stable Slurry

✍ Yuji Hotta; Huseyin Yilmaz; Takashi Shirai; Kazutoku Ohota; Kimiyasu Sato; Koji 📂 Article 📅 2008 🏛 John Wiley and Sons 🌐 English ⚖ 447 KB

Dispersion of nano- and submicron-sized

Dispersion of nano- and submicron-sized Al2O3 particles by wet-jet milling method

✍ Toshihiro Isobe; Yuji Hotta; Koji Watari 📂 Article 📅 2008 🏛 Elsevier Science 🌐 English ⚖ 371 KB

The agglomerated Al 2 O 3 powders with the primary particle size of 43-570 nm were dispersed into aqueous solvent by wet-jet milling process. The agglomerations in low solid-loaded suspensions were completely pulverized by wet-jet milling and the average particle sizes were in good agreement with pr

Fabrication of green and sintered bodies

Fabrication of green and sintered bodies prepared by centrifugal compaction process using wet-jet milled slurries

✍ Katsuya Sato; Yuji Hotta; Huseyin Yilmaz; Koji Watari 📂 Article 📅 2009 🏛 Elsevier Science 🌐 English ⚖ 585 KB

Properties of green and sintered bodies prepared by high-speed centrifugal compaction process (HCP) using wet-jet milled slurries were investigated. At 30 vol.% solids loading, the relative packing density of compacted body prepared from wet-jet milled slurry was 67%. On the other hand, the density

Effect of particle shape of active pharm

Effect of particle shape of active pharmaceutical ingredients prepared by fluidized-bed jet-milling on cohesiveness

✍ Tadashi Fukunaka; Kohta Sawaguchi; Boris Golman; Kunio Shinohara 📂 Article 📅 2005 🏛 John Wiley and Sons 🌐 English ⚖ 211 KB

Milling is a common procedure to improve bioavailability of many active pharmaceutical ingredients (APIs), which typically have low solubility in water. But such micronization can yield an increase in the cohesiveness of particles. Although particle cohesiveness is desirable for tablet strength in t