✦ LIBER ✦

Microstructure and mechanical properties of hydroxyapatite ceramics with zirconia dispersion prepared by post-sintering

✍ Scribed by Koji Ioku; Masahiro Yoshimura; Shigeyuki Sōmiya

Publisher: Elsevier Science
Year: 1990
Tongue: English
Weight: 710 KB
Volume: 11
Category: Article
ISSN: 0142-9612
DOI: 10.1016/0142-9612(90)90053-s

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Microstructure and properties of a TiAl

Microstructure and properties of a TiAl alloy prepared by mechanical milling and subsequent reactive sintering

✍ Fang Wenbin; Hu Lianxi; He Wenxiong; Wang Erde; Li Xiaoqing 📂 Article 📅 2005 🏛 Elsevier Science 🌐 English ⚖ 258 KB

A TiAl-based alloy with nominal composition of Ti-36 wt.% Al was prepared by a mechanical milling and reactive sintering route consisting of three basic steps: (1) mechanical milling of blended elemental Ti and Al powder mixture, (2) densification and consolidation of as-milled Ti/Al composite powde

Microstructure and mechanical properties

Microstructure and mechanical properties of ZrB2–MoSi2 ceramic composites produced by different sintering techniques

✍ Diletta Sciti; Frédéric Monteverde; Stefano Guicciardi; Giuseppe Pezzotti; Alida 📂 Article 📅 2006 🏛 Elsevier Science 🌐 English ⚖ 344 KB

Ceramic composites in the system ZrB2–(15–20vol% MoSi2) were produced by different densification techniques: pressureless sintering, hot-pressing and spark plasma sintering. Regardless of the sintering technique, the addition of 15–20vol% MoSi2 was beneficial for the densification of these composite

Effect of sintering temperature on micro

Effect of sintering temperature on microstructure and mechanical properties of highly porous silicon nitride ceramics produced by freeze casting

✍ Feng Ye; Jingyi Zhang; Haijiao Zhang; Limeng Liu 📂 Article 📅 2010 🏛 Elsevier Science 🌐 English ⚖ 481 KB

Highly porous Si 3 N 4 with macroscopically aligned pores were prepared by the unidirectional freeze casting process using liquid N 2 as refrigerant. The increased sintering temperature had no obvious influence on the porosity, but significantly promoted ␣ → ␤-Si 3 N 4 phase transformation and the g

Influence of iron powder particle size o

Influence of iron powder particle size on the microstructure and properties of Fe3Al intermetallics prepared by mechanical alloying and spark plasma sintering

✍ Qing He; Chengchang Jia; Jie Meng 📂 Article 📅 2006 🏛 Elsevier Science 🌐 English ⚖ 638 KB

Effect of Si/C ratio and their content o

Effect of Si/C ratio and their content on the microstructure and properties of Si–B–C–N Ceramics prepared by spark plasma sintering techniques

✍ Zhi-Hua Yang; De-Chang Jia; Xiao-Ming Duan; Ke-Ning Sun; Yu Zhou 📂 Article 📅 2011 🏛 Elsevier Science 🌐 English ⚖ 908 KB

Mechanical properties and microstructure

Mechanical properties and microstructure evolution of the nano WC–Co coatings fabricated by detonation gun spraying with post heat treatment

✍ S.Y. Park; M.C. Kim; C.G. Park 📂 Article 📅 2007 🏛 Elsevier Science 🌐 English ⚖ 636 KB