✦ LIBER ✦

Flow patterns in the calender gap of a counterrotating twin screw extruder

✍ Scribed by J. A. Speur; H. Mavridis; J. Vlachopoulos; L. P. B. M. Janssen

Publisher: John Wiley and Sons
Year: 1987
Tongue: English
Weight: 421 KB
Volume: 7
Category: Article
ISSN: 0730-6679
DOI: 10.1002/adv.1987.060070105

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Radical polymerization of styrene and st

Radical polymerization of styrene and styrene-butylmethacrylate in a counterrotating twin screw extruder

✍ A. J. van der Goot; L. P. B. M. Janssen 📂 Article 📅 1997 🏛 John Wiley and Sons 🌐 English ⚖ 189 KB 👁 1 views

This article describes the copolymerization of styrene-butylmethacrylate (St-BMA) and the homopolymerization of styrene (St) in a counterrotating twin screw extruder. The effect of prepolymerization on both the product properties and process was studied. It turned out that the process of reactive ex

The hydroxypropylation of starch in a se

The hydroxypropylation of starch in a self-wiping twin screw extruder

✍ Robbert A. de Graaf; Leon P. B. M. Janssen 📂 Article 📅 2003 🏛 John Wiley and Sons 🌐 English ⚖ 272 KB

Material distribution in the partially f

Material distribution in the partially filled zone of a twin-screw extruder

✍ Robbert A. de Graaf; Dolf. J. Woldringh; Léon P. B. M. Janssen 📂 Article 📅 1999 🏛 John Wiley and Sons 🌐 English ⚖ 151 KB 👁 2 views

Simulation of monomeric material transport in reactive extrusion revealed that two different situations can be distinguished in the partially filled zone of a twin-screw extruder. Material is transported from the bottom of the barrel to the top of the screw by drag or material remains on the bottom

Evolution of morphology and of chemical

Evolution of morphology and of chemical conversion along the screw in a corotating twin-screw extruder

✍ A. V. Machado; J. A. Covas; M. Van Duin 📂 Article 📅 1999 🏛 John Wiley and Sons 🌐 English ⚖ 298 KB 👁 1 views

A new sampling device is used to perform near-real-time investigations of physical and chemical processes occurring inside a laboratory twin-screw extruder. Polyamide-6 -ethylene propylene rubber (PA-6 -EPM) blending and styrene-maleic anhydride (SMA) imidation experiments are reported in terms of m

Mixing analysis of reactive polymer flow

Mixing analysis of reactive polymer flow in conveying elements of a co-rotating twin screw extruder

✍ David Strutt; Costas Tzoganakis; Thomas A. Duever 📂 Article 📅 2000 🏛 John Wiley and Sons 🌐 English ⚖ 247 KB 👁 1 views

In this study, the finite element method was used to investigate the effects of screw speed, entering peroxide distribution, and pressure-to-drag flow ratio on the mixing characteristics of steady non-isothermal reactive flows in a forward conveying element of a self-wiping twin screw extruder. The

Velocity measurements in the nip region

Velocity measurements in the nip region of a co-rotating twin-screw extruder using laser Doppler anemometry

✍ M. V. Karwe; S. Bakalis; V. Sernas 📂 Article 📅 1997 🏛 John Wiley and Sons 🌐 English ⚖ 245 KB 👁 1 views

The laser Doppler anemometer (LDA) technique has been successfully applied to measure the local velocities in the nip region of a twinscrew extruder. Tangential and axial components of velocity for heavy corn syrup were measured below and on either side of the nip. The experimental data show that th