✦ LIBER ✦

Fatigue fracture behaviour of carbon-fiber-reinforced modified bismaleimide composites

✍ Scribed by X.J. Xian; C.L. Choy

Publisher: Elsevier Science
Year: 1994
Tongue: English
Weight: 740 KB
Volume: 52
Category: Article
ISSN: 0266-3538
DOI: 10.1016/0266-3538(94)90011-6

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Behaviour of carbon fiber reinforced cem

Behaviour of carbon fiber reinforced cement composites in direct tension

✍ H.A. Toutanji; T. El-Korchi; R.N. Katz; G.L. Leatherman 📂 Article 📅 1993 🏛 Elsevier Science 🌐 English ⚖ 597 KB

The effect of carbon fibers on the tensile strength of cement paste matrix was experimentally and analytically investigated. The tensile strength values were obtained using the cementitious composites axial tensile technique (CCATr) [ 1,2]. The addition of 1, 1.5, 2, and 3 volume percent ofpolyacry

Mechanical and morphological properties

Mechanical and morphological properties of carbon fiber reinforced–modified epoxy composites

✍ B. R. Guduri; A. S. Luyt 📂 Article 📅 2006 🏛 John Wiley and Sons 🌐 English ⚖ 337 KB 👁 2 views

Effect of Fiber–Polymer Interactions on

Effect of Fiber–Polymer Interactions on Fracture Toughness Behavior of Carbon Fiber-Reinforced Epoxy Matrix Composites

✍ Soo-Jin Park; Mun-Han Kim; Jae-Rock Lee; Sunwoong Choi 📂 Article 📅 2000 🏛 Elsevier Science 🌐 English ⚖ 80 KB

The effect of anodic oxidation on high-strength polyacrylonitrilebased carbon fibers has been studied in terms of fiber surface energetics and fracture toughness of the composites. According to contact angle measurements based on the wicking rate of a test liquid, anodic oxidation leads to an increa

Fatigue delamination behaviour of unidir

Fatigue delamination behaviour of unidirectional carbon fibre/epoxy laminates reinforced by Z-Fiber® pinning

✍ Denis D.R. Cartié; Jean-Martin Laffaille; Ivana K. Partridge; Andreas J. Brunner 📂 Article 📅 2009 🏛 Elsevier Science 🌐 English ⚖ 764 KB

Z-Pin reinforced carbon-fibre epoxy laminates were tested under Mode I and Mode II conditions, both quasi-statically and in fatigue. Test procedures were adapted from existing standard or pre-standard tests. Samples containing 2% and 4% areal densities of carbonfibre Z-pins (0.28 mm diameter) were c

Cyclic fatigue behavior of carbon fiber

Cyclic fatigue behavior of carbon fiber reinforced vinylester resin composites manufactured by RTM and VARI

✍ N. Himmel; C. Bach 📂 Article 📅 2006 🏛 Elsevier Science 🌐 English ⚖ 718 KB

The mechanical behavior of [0°] 8 unidirectional, [+45°/0°/À45°/90°] S quasi-isotropic and [+45°/À45°] 3S angle-ply laminates produced by pressure or vacuum assisted resin infusion from toughened vinylester resin systems with unidirectional carbon fiber fabric reinforcement was investigated. The stu

Interfacial Characteristics and Fracture

Interfacial Characteristics and Fracture Toughness of Electrolytically Ni-Plated Carbon Fiber-Reinforced Phenolic Resin Matrix Composites

✍ Soo-Jin Park; Yu-Sin Jang 📂 Article 📅 2001 🏛 Elsevier Science 🌐 English ⚖ 147 KB

The electrolytic plating of metallic nickel on a carbon fiber surface has been carried out in order to improve the interfacial adhesion and the mechanical properties in carbon fiber/phenolic matrix composite systems. The surface and the mechanical interfacial properties of composites are characteriz