✦ LIBER ✦

Fabrication, microstructure and mechanical properties of novel cemented hard alloy obtained by mechanical alloying and hot-pressing sintering

✍ Scribed by Zhuhui Qiao; Xianfeng Ma; Wei Zhao; Huaguo Tang; Shuguang Cai; Bo Zhao

Publisher: Elsevier Science
Year: 2007
Tongue: English
Weight: 545 KB
Volume: 460-461
Category: Article
ISSN: 0921-5093
DOI: 10.1016/j.msea.2007.01.007

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

A Novel Cemented Hard Alloy Prepared by

A Novel Cemented Hard Alloy Prepared by Mechanical Alloying and Hot-Pressing Sintering

✍ Z. Qiao; X. F. Ma; W. Zhao; H. Tang; S. Cai; B. Zhao 📂 Article 📅 2007 🏛 John Wiley and Sons 🌐 English ⚖ 189 KB 👁 2 views

Synthesis, Microstructure and Mechanical

Synthesis, Microstructure and Mechanical Properties of Al40W60 Bulk Alloy Obtained by Mechanical Alloying and Hot-Pressing

✍ C. J. Zhu; X. F. Ma; W. Zhao; H. G. Tang; J. M. Yan; S. G. Cai 📂 Article 📅 2005 🏛 John Wiley and Sons 🌐 English ⚖ 355 KB 👁 2 views

ZrC particle reinforced Al–4 wt.% C

ZrC particle reinforced Al–4 wt.% Cu alloy composites fabricated by mechanical alloying and vacuum hot pressing: Microstructural evaluation and mechanical properties

✍ Hülya Kaftelen; M. Lütfi Öveçoğlu; Hani Henein; Hüseyin Çimenoğlu 📂 Article 📅 2010 🏛 Elsevier Science 🌐 English ⚖ 736 KB

Microstructure and mechanical properties

Microstructure and mechanical properties of Cu-based bulk amorphous alloy billets fabricated by spark plasma sintering

✍ Chang Kyu Kim; Han Sang Lee; Seung Yong Shin; Jae Chul Lee; Do Hyang Kim; Sungha 📂 Article 📅 2005 🏛 Elsevier Science 🌐 English ⚖ 506 KB

In this study, Cu-based bulk amorphous alloy billets were fabricated by a powder metallurgy route, and their microstructure and mechanical properties were investigated. Rapidly solidified amorphous powders were produced by a conventional N 2 gas atomization method. In order to consolidate amorphous

Microstructures and properties of SiB0.5

Microstructures and properties of SiB0.5C1.5N0.5 ceramics consolidated by mechanical alloying and hot pressing

✍ Zhi-Hua Yang; Yu Zhou; De-Chang Jia; Qing-Chang Meng 📂 Article 📅 2008 🏛 Elsevier Science 🌐 English ⚖ 831 KB

Microstructure and properties of a TiAl

Microstructure and properties of a TiAl alloy prepared by mechanical milling and subsequent reactive sintering

✍ Fang Wenbin; Hu Lianxi; He Wenxiong; Wang Erde; Li Xiaoqing 📂 Article 📅 2005 🏛 Elsevier Science 🌐 English ⚖ 258 KB

A TiAl-based alloy with nominal composition of Ti-36 wt.% Al was prepared by a mechanical milling and reactive sintering route consisting of three basic steps: (1) mechanical milling of blended elemental Ti and Al powder mixture, (2) densification and consolidation of as-milled Ti/Al composite powde