✦ LIBER ✦

Extruder scale-up in a corotating twin-screw extrusion compounding process

✍ Scribed by Enno E. Agur

Publisher: John Wiley and Sons
Year: 1986
Tongue: English
Weight: 496 KB
Volume: 6
Category: Article
ISSN: 0730-6679
DOI: 10.1002/adv.1986.060060208

No coin nor oath required. For personal study only.

📜 SIMILAR VOLUMES

Evolution of morphology and of chemical

Evolution of morphology and of chemical conversion along the screw in a corotating twin-screw extruder

✍ A. V. Machado; J. A. Covas; M. Van Duin 📂 Article 📅 1999 🏛 John Wiley and Sons 🌐 English ⚖ 298 KB 👁 2 views

A new sampling device is used to perform near-real-time investigations of physical and chemical processes occurring inside a laboratory twin-screw extruder. Polyamide-6 -ethylene propylene rubber (PA-6 -EPM) blending and styrene-maleic anhydride (SMA) imidation experiments are reported in terms of m

Functionalization of polypropylene with

Functionalization of polypropylene with oxazoline and reactive blending of PP with PBT in a corotating twin-screw extruder

✍ Tommi Vainio; Guo-Hua Hu; Morand Lambla; Jukka Seppälä 📂 Article 📅 1997 🏛 John Wiley and Sons 🌐 English ⚖ 338 KB 👁 2 views

The aim of this study was to prepare a compatibilized PP/PBT blend in a twin-screw extruder, using oxazoline-functionalized PP. First we prepared the functionalized PP (PP-g-OXA), and then we used it as a compatibilizer in the subsequent reactive blending stage. Polypropylene was successfully functi

Experimental analysis of the kneading di

Experimental analysis of the kneading disk region in a co-rotating twin screw extruder: Part 2. glass-fiber degradation during compounding

✍ Y. Shimizu; S. Arai; T. Itoyama; H. Kawamoto 📂 Article 📅 1997 🏛 John Wiley and Sons 🌐 English ⚖ 269 KB 👁 2 views

The fiber degradation in the kneading disk region of a corotating twin screw extruder was studied with a closed single-stage co-rotating twin screw extruder as a model for the analysis. In a previous article, we reported that the stress in the kneading zone was proportional to the screw torque. In t

Modeling of industrial nylon-6,6 polycon

Modeling of industrial nylon-6,6 polycondensation process in a twin-screw extruder reactor. I. phenomenological model and parameter adjusting

✍ Reinaldo Giudici; Cláudio Augusto Oller Do Nascimento; Isabel Capocchi Beiler; N 📂 Article 📅 1998 🏛 John Wiley and Sons 🌐 English ⚖ 355 KB 👁 2 views

This article describes a mathematical model for the finishing stage of nylon-6,6 polycondensation in a twin-screw extruder reactor. In the model, the extruder is conceptually divided into two regions. The first one is the partially filled degassing zone, which is operated under low pressure and wher

Modeling of industrial nylon-6,6 polymer

Modeling of industrial nylon-6,6 polymerization process in a twin-screw extruder reactor. II. Neural networks and hybrid models

✍ Claudio Augusto Oller Nascimento; Reinaldo Giudici; Natália Scherbakoff 📂 Article 📅 1999 🏛 John Wiley and Sons 🌐 English ⚖ 174 KB 👁 2 views

This article describes the application of neural networks and hybrid models to the finishing stage of nylon-6,6 polycondensation in a twin-screw extruder reactor. A planned experiment in the industrial and in the pilot plant was employed to build the neural network and the hybrid model. The hybrid m