𝔖 Bobbio Scriptorium
✦   LIBER   ✦

Effect of glycol and filler types on some polymeric composite properties

✍ Scribed by J. N. Asaad; S. L. Abd-El-Messieh

Publisher
John Wiley and Sons
Year
2008
Tongue
English
Weight
592 KB
Volume
109
Category
Article
ISSN
0021-8995

No coin nor oath required. For personal study only.

✦ Synopsis

Abstract

Two unsaturated polyesters based on maleic anhydride, phthalic anhydride, and sebasic acid with each of linear 1,6‐hexanediol (PE~L~) and cyclic 1,4‐cyclohexanediol (PE~C~) were prepared. Their structures were characterized by IR and ^1^H NMR spectra. Their composites were prepared by mixing different ratios (60, 70, and 80%) with talc and kaolin with polyester/styrene mixture. The effect of linear and cyclic glycols and the effect of filler type and concentration of these composites were studied in terms of their electrical properties and the hardness before and after aging. The thermal behavior of styrenated polyesters and their composites was studied using thermogravimetric analysis. It has been found that both fillers increase the thermal stability and decrease the weight loss. The permittivity ε′ and the dielectric loss ε″ were measured in the frequency range 100 Hz up to 100 kHz at room temperature 25°C ± 1. The polyester composite samples containing 70% filler lead to good electrical properties in addition to its resistance to thermal aging. The hardness value was increased by increasing the filler content before and after aging. The polyester composites based on cyclic glycol and loaded with 80% kaolin gave the highest hardness values. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008

📜 SIMILAR VOLUMES

Effects of filler–filler and polymer–fil
Effects of filler–filler and polymer–filler interactions on rheological and mechanical properties of HDPE–wood composites
✍ Han-Xiong Huang; Jing-Jing Zhang 📂 Article 📅 2009 🏛 John Wiley and Sons 🌐 English ⚖ 599 KB

## Abstract High‐density polyethylene (HDPE)–wood composite samples were prepared using a twin‐screw extruder. Improved filler–filler interaction was achieved by increasing the wood content, whereas improved polymer–filler interaction was obtained by adding the compatibilizer and increasing the mel

Effect of filler type and concentration
Effect of filler type and concentration on some mechanical and electrical properties of poly(methyl methacrylate)
✍ A. B. Moustafa; A. Faizalla; B. M. Abd El Hady 📂 Article 📅 1998 🏛 John Wiley and Sons 🌐 English ⚖ 132 KB 👁 1 views

Polymer composites of poly(methyl methacrylate) (PMMA) and cuprous oxide (Cu 2 O), magnesium oxide (MgO), copper biphthalocyanine, iron (II) chloride (FeCl 2 ), and iron metal were prepared by different filler-to-polymer percentages of 10, 20, 30, 40, and 50%. With increasing filler concentration, b

Alumina powder/Bis-GMA composite: Effect
Alumina powder/Bis-GMA composite: Effect of filler content on mechanical properties and osteoconductivity
✍ Kobayashi, Masahiko ;Shinzato, Shuichi ;Kawanabe, Keiichi ;Neo, Masashi ;Matsush 📂 Article 📅 2000 🏛 John Wiley and Sons 🌐 English ⚖ 686 KB

Three composites consisting of alumina powder dispersed in a bisphenol-a-glycidyl methacrylate (Bis-GMA) matrix were prepared and evaluated to assess the effect of alumina powder content on the mechanical properties and osteoconductivity of the composite. The alumina powder composites (APC) consiste