𝔖 Bobbio Scriptorium
✦   LIBER   ✦

Development of a Ceramic Micro Heat Exchanger – Design, Construction, and Testing

✍ Scribed by B. Alm; R. Knitter; J. Haußelt

Publisher
John Wiley and Sons
Year
2005
Tongue
English
Weight
377 KB
Volume
28
Category
Article
ISSN
0930-7516

No coin nor oath required. For personal study only.

✦ Synopsis

Abstract

This article presents the development of a ceramic micro heat exchanger. Starting from its geometrical design, results obtained from a simplified simulation of the heat exchanger efficiency will be given. The alumina microcomponents were manufactured by a rapid prototyping process chain. Here, stereolithography was combined with a low‐pressure injection molding process for the rapid and precise manufacturing of ceramic components down to the micrometer range. A micro heat exchanger, joined from sintered components using a glass solder, was applied as a prototype and checked for its performance at a system pressure of 8 bar.

📜 SIMILAR VOLUMES

Heat and mass transfer model of a Ground
Heat and mass transfer model of a Ground Heat Exchanger: theoretical development
✍ M. Piechowski 📂 Article 📅 1999 🏛 John Wiley and Sons 🌐 English ⚖ 196 KB 👁 3 views

A new approach to the simulation of a horizontal type Ground Heat Exchanger is proposed resulting in a better accuracy and at the same time a reduced computational e!ort. These results come from the concentration of the computational e!ort at the locations with the largest temperature and moisture g

Design and construction of a micro-inden
Design and construction of a micro-indenter for tribological investigations
✍ K. S. Tan; A. W. Hassel; M. Stratmann 📂 Article 📅 2005 🏛 John Wiley and Sons 🌐 English ⚖ 172 KB

Characterisation of erosion contact conditions remains a challenge due to the chaotic morphology of eroded surfaces. The present work presents details on the design and construction of a low load micro-indenter to investigate the initial stages of particle impact. Spherical ZrO 2 particles and angul

Design, realization, and test of a 900 M
Design, realization, and test of a 900 MHz ceramic oscillator
✍ Stefano Pisa; Emanuele Piuzzi; Pasquale Tommasino; Alessandro Trifiletti; Alessa 📂 Article 📅 2007 🏛 John Wiley and Sons 🌐 English ⚖ 384 KB

## Abstract The design of a 900 MHz ceramic oscillator, delivering a power of 10 dBm, has been carried out by using the negative‐resistance condition. A new procedure based on the Nyquist criterion, implemented within microwave CADs has been used to test the onset of oscillations at the desired fre

Design, development and testing of a nov
Design, development and testing of a novel non-tracking solar cooker
✍ N. M. Nahar 📂 Article 📅 1998 🏛 John Wiley and Sons 🌐 English ⚖ 170 KB 👁 2 views

A novel solar cooker that does not require any tracking, has been designed, fabricated and tested and its performance has been compared with the hot-box solar cooker. The performance of the novel solar cooker is almost similar with the hot-box solar cooker though it is kept fixed while the hot box i

Thermal design of a closed cabinet with
Thermal design of a closed cabinet with a heat exchanger for inner air cooling
✍ Takashi Kobayashi; Mitsunori Nakamura; Tetsuro Ogushi; Akifumi Iwamaru; Masao Fu 📂 Article 📅 2001 🏛 John Wiley and Sons 🌐 English ⚖ 378 KB 👁 1 views

## Abstract This paper describes a thermal design and simulation method of a closed cabinet with a heat exchanger for inner air cooling. In the controller system that we used for this research, the cabinet is equipped to be outdoors, and the cabinet is sealed to prevent the introduction of dust. Be